Object Listing

Round finial with a short slightly curved shaft that ends in a point.

Round finial set at a slight angle to the shaft. Upper shaft has a sheath of leather around it.

Club with large 'bun-shaped' finial. Its shaft is decorated with 4 bands of two-tone wirework

Spherical finial with two shallow hemispherical concave indentations in its bottom and top surface. that angle towards the front. The surface of the finial without facets is carved with parallel vertical grooves across its surface.

Round finial with a slightly undulating shaft.

Spherical finial with faceted sides and two shallow hemispherical concave indentations in its bottom and top surface that angle towards the front. The finial has a deep vertical crack.

Round finial and slightly curving shaft with a small unravelling band of wire work. There is a pale section just below the finial where a band of some sort would have been positioned - now missing.

Club with ovoid finial set off-centre at the end of the shaft. It has wide concentric grooves facing outward on either side of the finial.

Spherical finial with two shallow hemispherical concave indentations in its bottom and top surface - the lower one angled upwards towards the front. There is a pale section in the centre of the shaft where a band of some sort would have been positioned - now missing.

Short shaft with a spherical finial offset to one side of the shaft. Finial has two shallow hemispherical concave indentations in its bottom and top surface

Round finial with deeply grooved vertical facets across its entire surface.

Spherical finial with two small shallow hemispherical concave indentations in its bottom and top surface - the lower one angled upwards towards the front. The finial is set slightly off-centre from the staff.

Ovoid/onion-shaped finial. Shaft tapers to a point

Club with large 'bun-shaped' finial decorated with vertical grooved lines. Its shaft is sheathed with a band of leather and 7 metal rings - 2 above the band and 5 below.

Spherical finial with two shallow hemispherical concave indentations in its bottom and top surface - the lower one angled upwards towards the front.

Spherical finial with two shallow hemispherical concave indentations in its bottom and top surface. The lower one angles towards the front. There is a large crack in the finial. The shaft is decorated with one metal band and one wire work band

Barrel-shaped finial with flat sides. shaft flares slightly at its base.

Ovoid finial, Entire shaft and finial sheathed in Wirework. There are two additional wire bands near the base.

Ovoid shaped finial with 4 equal segments of grooved lines alternating with 4 smooth surfaced segments arranged symmetrically around the finial. These begin at the top of the finial and end a small distance away from the shaft.

Short handled club with a ovoid finial with an indented top and bottom

Spherical finial with two shallow hemispherical concave indentations in its bottom and top surface - the lower one angled upwards towards the front. A raised band of slanted grooved lines is positioned along the shaft near the finial end

Truncated spherical finial with two shallow hemispherical concave indentations in its bottom and top surface - the lower one angled upwards towards the front. The vertical surface of the finial is covered with a linear grooved pattern

Spherical finial. The shaft is sheathed in 4 bands of two-toned wire work. The upper band covers about 1/5 of the shaft length and is the largest.

Finial is a flat round disk with a round mirror held in place with small metal nails flush with the surface. The outer edge is indented along its curve so that it has a shallow gully running around it. This is set flat sides facing out on top of the shaft.

Staff with a round ball-shaped finial. The finial and the upper part of the shaft are embellished with short tubular projections.

Ovoid/onion-shaped finial. Shaft tapers to a rounded point

Club with round finial covered with conical brass studs. Its shaft is sheathed for most of its length with wire work. This stops short of the bottom which has one small band above an band at the base. There is a hole drilled through at the base

Short curved shaft with a large organic ovoid finial projecting from one side of the shaft. The finial has a wide indentation on its top surface and another shallower one in its bottom surface.