Object Listing

Wooden staff with three horizontal sections that project beyond the shaft of the staff like wings. These are spaced along the upper section of the staff . The shaft sections between these is covered with a beadwork sheath. These wings have horizontal V-designs in pokerwork with points facing inwards towards the shaft.

Amphora-like shape resting an inverted truncated cone. It has two wing-like handles and is covered with grooves parallel lines over the entire surface of the vessel - on the base the lines are slanted; on the body vertical and on the handles horizontal.

Roughly rectangular trough shaped container with four flat tapered legs at each corner. These are decorated with parallel grooved lines. From each end of the lower edge of the bowl and from the centres of its long sides project four cylindrical open arched shaped loops.

Oval platter on four legs (one broken) with a long handle at one end and curved hollow projection at the other end. The long handle has a foot about 1/5 of the way towards its end and bands of wire work decorating the shaft

Horizontal rectangular headrest with crossbar curving slightly up at ends. The body is punctuated by two vertical rectangular holes and the base is a flat plane. Two arrows in relief carving point up from the base at either end. On the face of each end are twinned anthropomorphic figures with largish heads that stand to attention as end supports.

Horizontal rectangular block headrest with flat crossbar that has linear designs at either end of upper surface. Geometric designs such as checkerboard, triangles, interlocking Vs in relief embellish the two largest surfaces

Globe-shaped container on three rectangular legs with bowl-shaped lid. The lid had three short rectangular legs and the containers legs are wide at their tops and narrow towards their bases with shapes like obtuse triangles. The whole is decorated with zones with parallel grooved lines. There are numerous cracks in the body of the vessel.

Large ovoid vessel with two circular rings circling the body but spaced away by the base support. The two rings are joined by 4 pillars and these rest on a base with two horizontal struts and four legs. All the elements are covered with deeply carved grooved parallel lines.

Snuff-spoon comb with elongated fan-shaped spoon with convex pointed end. The bowl ha two circular indentations in it. The neck has a diamond shape below the spoon bowl and this is joined by a rectangular section joined by a diamond shape to another rectangular section . A rectangular section follows and from this a shoulder with 5 tines emerging from it. The spoon is embellished with small areas of linear designs carved into the surface and blackened and serrating on the two wider neck sections. The whole is curved along its length.

Snuff-spoon comb with leaf-shaped bowl, neck and 2 tines emerging from it. The neck is embellished back and front with linear designs carved into the surface and blackened.

Comb with a hollow rectangular section from which 3 short tines (one is broken off) emerge above and 4 longer times emerge below. On the longer sides of the triangle are outward facing triangles and 5 and 3 concentric circular designs on the longer and shorter sides respectively.

Snuff-spoon comb with leaf-shaped bowl, neck, shoulder and 4 tines emerging from it. The neck and shoulder are embellished back and front with circular designs with dots in centre carved into the surface and blackened.

Small comb with handle and 10 tines. The handle is embellished with triangular and concentric circle designs carved into the surface and blackened. The handle tilts upwards at a low slant

Small spoon-comb combination with 2 tines. The neck region is embellished with a cross-hatched design and just below are two circled with lines through them. These are carved into the surface and blackened. From the side the neck region is arched upwards between the spoon bowl and the tines.

Small spoon-comb combination with 3 tines. The neck region is embellished with 6 circles along the front and a cross-hatched design. Just below is one set of concentric circles . These designs are carved into the surface and blackened. From the side the neck region is arched upwards between the spoon bowl and the tines.

Small spoon-comb combination with 4 tines. The neck region is embellished with triangular designs along the front and a cross-hatched design at the back. Just below is a set of 4 concentric circles joined by diagonal lines . These designs are carved into the surface and blackened. The whole spoon is curved slightly upwards along its whole length.

Small spoon-comb combination with 5 tines. The bowl is leaf-shaped. The neck region is embellished with linear designs along the front and a cross-hatched design at the back. Just below is a set of 3 concentric circles . These designs are carved into the surface and blackened. From the side the neck region is arched upwards between the spoon bowl and the tines.

Snuff-spoon comb with half-moon-shaped bowl, ovoid neck with hold in centre, round shoulder and 6 tines emerging from it. The neck and shoulder are embellished in the front with circular designs with dots in centre carved into the surface and blackened. The back has inward facing triangles around the neck and circle and dot design on the shoulder

Snuff-spoon comb with half-moon-shaped bowl, with 5 tines below and a truncated diamond shape above emerging from it. Only the back of the spoon bowl is embellished with circular designs with dots in centre carved into the surface and blackened.

Snuff-spoon comb with leaf-shaped bowl, neck and one tine emerging from it. The neck is embellished at the back with cross hatched linear designs carved into the surface and blackened. The front has a line of 5 circular designs linked by a line down their centres and 3 horizontal lines at the end of the row.

Snuff-spoon with leaf-shaped bowl, neck and one tine emerging from it. The neck is embellished at the back with inward -facing triangular designs carved into the surface and blackened. The front has 4 vertical lines with small triangles projecting from these lines. l

Small spoon with single tine that curves slightly along its length inwards from tip to tail. The bowl is leaf-shaped. The neck region is embellished with linear designs and one concentric circle along the front and a cross-hatched design at the back. These designs are carved into the surface and blackened.

Small spoon with single tine that curves slightly along its length inwards from tip to tail. The bowl is leaf-shaped. The neck region is embellished with a vertical linear designs in the front and a cross-hatched design at the back. These designs are carved into the surface and blackened.

Small spoon with single tine that curves slightly along its length inwards from tip to tail. The bowl is leaf-shaped. The neck region is embellished with a vertical linear designs in the front and a cross-hatched design at the back. These designs are carved into the surface and blackened.

Small spoon with single tine that curves slightly along its length inwards from tip to tail. The bowl is leaf-shaped. The neck region is embellished with linear designs with zigzags running down their length back and front. Just below the bowl is a s design of 4 inward facing triangles with two outer triangles filled with Zig-zag designs. These designs are carved into the surface and blackened.

Small spoon with single tine that curves slightly along its length inwards from tip to tail. The bowl is leaf-shaped.

Small spoon with single tine. The bowl is leaf-shaped. The neck region is embellished with two vertical rows of concentric circles with central dots and one horizontal row framed by lines. These designs are carved into the surface and blackened.

Small spoon with handle that is rounded at its end. The bowl is leaf-shaped. The neck region is embellished with a few irregular linear designs. These designs are carved into the surface and blackened.

Ovoid container on three feet with bowl shaped lid with three 4-sided short legs. The legs of the container flare outwards towards their base. The whole is decorated with bands and rows of small triangles carved into the wood. The lid has a crack running across its upper surface and down its sides.